Installation · Hinged door

How to install a hinged door

Eighteen steps, from checking the opening to the cover strip snapped into place. This is the sequence we give our installers, transcribed from the installation sheet.

La porta a battente è quella che si monta più spesso, ed è anche quella in cui si fa prima a sbagliare l’ordine delle operazioni. Sotto trovi i passi nella successione in cui vanno eseguiti. Tre indicazioni del reparto sono messe a parte, perché non sono passaggi ma consigli: due riguardano dove nascondere le viti, uno riguarda la schiuma.

01 · before you start

Tools and checks

The sheet opens with what you need to have to hand: tape measure, gloves, screwdriver drill, polyurethane foam, screwdriver, hammer and silicone gun. Then two checks that are well worth the five minutes they take.

  1. Installation tools

    Metti insieme tutto prima di aprire l’imballo. La schiuma e il silicone servono in fondo, ma cercarli a metà lavoro con la porta ferma sui cunei è il modo più rapido per spostare qualcosa che era già in bolla.

  2. Check the internal size of the subframe

    Measure the opening inside il controtelaio, non il foro nel muro. È il controllo che decide se la porta entra: farlo adesso costa un minuto, scoprirlo con l’anta già in mano costa il viaggio di ritorno.

  3. The key supplied is attached to the frame

    Non è nella scatola degli accessori: la trovi fissata al telaio della porta. Vale la pena saperlo prima di mettere sottosopra l’imballo cercandola.

02 · installation

From fitting to testing

Nove passi. La porta entra nel vano, si blocca, si fissa e si prova: la sequenza finisce con l’anta che apre e chiude, prima che la schiuma renda tutto definitivo.

  1. Remove the bottom spacer

    The spacer holds the frame together during transport. Remove it before sliding the door into the opening.

  2. Inserisci la porta nell’apertura

    The frame goes into the subframe. From here on, every movement shifts the geometry, so take your time.

  3. Wedge the door in place

    The wedges hold the frame in position while it is being fixed. They are temporary, but everything that follows depends on how it sits now.

  4. Fit the handle supplied

    Si monta ora, non alla fine: serve per provare l’apertura al passo dodici, quando c’è ancora modo di correggere.

  5. Pull the gasket out of the frame

    The gasket comes out of its groove to free the spot where the fixing screws go. It goes back in at step eleven.

  6. Fix the door to the subframe

    The screws go into the groove left free by the gasket.

  7. The strike plate screws

    Same principle on the lock side: the screws go behind the strike plate.

  8. Put the gasket back

    It goes back into its groove and covers the screws you have just fitted.

  9. Check that it works

    Apri e chiudi prima di passare alla schiuma. Questo è l’ultimo momento in cui una correzione costa poco: dopo, il telaio è annegato.

The two tips on the screws

The sheet points out both of them, and they say the same thing from two sides: fix the door to the subframe by inserting the screws behind the gasket, and insert the screws behind the strike plate. In both cases you avoid visible screws and the installation stays neater. The hold does not change: what changes is what you will see ten years from now.

03 · finishing

Foam, trims, cover strips

Six steps. From here on there is no going back: the foam fills, the trims are cut to size and the cover strips close everything off.

  1. Fill the gaps with foam

    The foam goes into the space between the frame and the masonry. Handle it with care: it can spill out. È l’avvertenza scritta sul foglio, ed è l’unica del documento.

  2. Cut the trims

    They are cut to the size of the finished opening, not before.

  3. Apply silicone behind the trim

    The silicone goes on the back, where it cannot be seen, and holds the trim against the wall.

  4. Snap in the cover strips

    They press-fit into their groove and close off the perimeter.

  5. Installation is complete

    The door is installed, fixed, tested and finished.

If something is not right

The door rubs or does not close flush

It happens, and almost always nothing needs to be taken apart: it just needs adjusting. The concealed hinges have three adjustments and the strike plate has one, and they are done with two Allen keys in ten minutes.

The other guides

If your door is not a hinged door

Flush-to-wall door

The steps for drywall and for masonry, with the point of no return for each.

Go to the guide

Pocket sliding door

Due sequenze distinte: sei operazioni per il controtelaio a parete grezza, tredici per l’anta a intonaco finito.

Go to the guide

Magical wall-mounted sliding door

The door that slides along the wall: allowances on the opening, carriage to fix to the wall and the safety stop that prevents unhooking.

Go to the guide

The original sheet

This page is a transcription of the FIP installation sheet for the hinged door. If you prefer the document with the drawings, here it is (in Italian).