Installation · Magical wall-mounted sliding door

How to install a Magical sliding door

Eighteen steps, from the measurement on the wall to the side end caps screwed in. This is the sequence we give our installers, transcribed from the installation sheet.

The Magical runs in front of the wall: the carriage is fixed to the wall above the opening and the aluminum track is already fixed to the door panel. So the installation starts with a measurement taken on the wall and ends with the cover snapped into place. The numbers that decide the job are few, and they are all in the first six steps.

01 · measurements

The wall and the door

The sheet opens with the survey and the allowances to apply. These are the two boxes on which everything else depends: this is where you decide how wide and how tall the door will be compared with the opening. The other two boxes in this first row are not operations; they are reference drawings.

  1. Measure the wall

    Take the measurement on the pre-squared wall. You start from the opening, already squared: the measurement you take now is the one used to calculate the allowances in the next step.

  2. The allowances to apply

    There are three, and the sheet gives them like this: Width + 10 cm for partial opening, Width + 22 cm for full opening, Height + 8 cm. The choice between ten and twenty-two centimeters is not about looks: it decides whether the opening is left completely clear when the door is open.

  3. Top detail

    This is not a step to carry out: it is the drawing of the top assembly, the one that is fixed to the wall from step six onwards.

  4. Bottom detail

    The matching drawing of the lower part.

The figures on the sheet, all together

There are five, and no others: width + 10 cm per l’apertura parziale, width + 22 cm for full opening, height + 8 cm, holes 8 mm in diameter and 40 mm deep, carriage positioned 3 cm higher della misura del binario. L’unico margine di recupero, alla fine, è il centimetro in più o in meno del passo tredici.

02 · the carriage

Fixing to the wall

Cinque passi. Si misura l’attacco del binario, si riporta la quota sul muro con tre centimetri di scarto, si fora, si avvita. È la parte che non si corregge più: i fori restano dove sono stati fatti.

  1. Misura l’attacco del binario

    Misurare l’attacco del binario in alluminio fissato sul pannello porta. The rail comes already fitted to the door: the height to transfer to the wall is read from there.

  2. Transfer the height to the wall, three centimeters higher

    Position the carriage 3 cm higher than the measurement of the rail on the door panel and mark the fixing holes on the wall. The three centimeters are the clearance that lets the door hook on and then drop into position: without it, the rail will not go into the carriage.

  3. Drill the wall

    Drill with an 8 mm diameter masonry bit to a depth of 40 mm. The diameter and depth are those of the wall plugs supplied.

  4. Screw the carriage to the wall

    After inserting all the wall plugs into the wall, position the carriage and screw it firmly to the wall. Tutti i tasselli prima, il carrello dopo: appoggiarlo a metà tassellatura significa reggerlo con una mano mentre si fora con l’altra.

  5. Release the end stop

    Release the end stop to let the rail go in. This is the end-of-travel stop: as long as it stays locked, the door rail cannot slide into the carriage.

03 · the door

Hanging, adjustment, finishing

Nine boxes. The door goes into the carriage, the height is adjusted, the safety stop that prevents unhooking is fitted and everything is closed off with the cover and the end caps. Two of the boxes are cross-section views: they show where the safety stop goes, they are not operations.

  1. The adjustment screw

    This adjustment screw is used to raise or lower the door panel. Vale la pena individuarla prima di agganciare: è quella che al passo tredici recupera l’errore.

  2. Fit the door into the carriage

    Insert the door into the carriage. The rail fixed to the panel slides into the carriage you have just screwed to the wall.

  3. Door hung

    The door is hung. From here the door stands on its own and slides.

  4. Regola l’altezza

    È possibile regolare l’altezza della porta di +- cm. 1. One centimeter up or down: that is all the margin left after drilling, and it is used to bring the door level with the floor.

  5. Fit the safety stop

    Fit the safety stop to prevent the panel from unhooking. This is the part that stops the door from coming out of the carriage: it is not an accessory, it is what holds the panel up.

  6. The cross-section view

    Cross-section view of the top part, with the safety stop to be fitted. Il disegno è etichettato dall’alto verso il basso: muro, carrello, binario, pannello porta. La freccia indica il punto in cui va la sicurezza.

  7. Safety stop fitted

    Safety stop fitted. The same drawing with the part in place: the carriage is fixed to the wall and the rail is engaged in the door.

  8. Finish with the cover and end caps

    Snap on the cover and screw on the side end caps. The cover hides the carriage and the end caps close off both ends.

  9. The finished result

    Here is the finished result. The door slides along the wall and the mechanism is no longer visible.

The other guides

If your door is not a Magical

Pocket sliding door

Il caso opposto: la porta sparisce dentro il muro. Due sequenze distinte, una per il controtelaio a parete grezza e una per l’anta a intonaco finito.

Go to the guide

Hinged door

Eighteen steps, from checking the inside measurement of the subframe to snapping in the cover strip.

Go to the guide

Flush-to-wall door

The steps for drywall and for masonry, with the point of no return for each.

Go to the guide

The original sheet

This page is a transcription of the FIP installation sheet for the Magical sliding door. If you prefer the document with the drawings, here it is (in Italian).